How to Specify LED Downlights for Hotel Projects: Cutout, UGR, CRI and Dimming

Hotel lighting is specified once and then lived with for a decade. Unlike a retail fit-out, guest rooms, corridors and lobbies cannot easily be re-opened for a second attempt: the ceiling build-up, the cutouts and the control wiring are all locked in during construction. A downlight that looks good in a showroom but produces glare at a pillow, or one that shifts colour between adjacent rooms, becomes a permanent complaint rather than a punch-list item.

This guide follows the specification sequence our project engineers use when preparing hotel tender packages, IES files and DIALux layouts. It is written for lighting designers, MEP consultants and hotel procurement teams who need to defend a fixture choice on paper before a sample is ever ordered.

1. Fix the ceiling build-up and cutout first

Cutout is the least glamorous and most expensive parameter to get wrong. It must be agreed with the ceiling contractor, the fire-rated assembly and the HVAC layout before the fixture schedule is issued. A 5 mm mismatch on a trimless or gypsum downlight means on-site reaming, broken plaster edges and a visible shadow gap.

For recessed fixtures, record three dimensions separately: the ceiling cutout, the overall flange or trim diameter, and the required void depth above the ceiling. Deep anti-glare optics need more recess depth than a shallow flat-panel downlight; a 75 mm cutout fixture with a 120 mm deep housing will not fit under a beam or a duct run. Surface-mounted IP65 downlights are the pragmatic fallback when the void is too shallow — several ranges offer both recessed and surface versions of the same optical family, which keeps the look consistent across a floor.

Our commercial lighting range covers cutouts from 30 to 200 mm, and the Xuanwu series spans 75–200 mm across eight sub-series, so one visual language can be held from a 75 mm corridor light to a 200 mm lobby fixture.

2. Set the glare limit before you look at style

Unified Glare Rating (UGR) is the number that separates a comfortable guest room from one that feels harsh, but it is frequently quoted without context. UGR is a property of the whole installation — luminaire, position, room reflectance and viewing direction — not of the bare fixture. A luminaire marketed as “low glare” can still produce UGR above 19 if it sits directly in the normal field of view above a bed.

Specify the target at room level: UGR < 19 for guest rooms, spa and reading areas, and UGR < 22 for corridors, lift lobbies and back-of-house. Then ask for the photometric file, not just a datasheet claim. Deep-cup reflectors, recessed LED position and black baffles all reduce high-angle light; the trade-off is a narrower useful beam and slightly lower delivered lumens, which must be accounted for in the layout.

Practical placement rule: keep downlights out of the direct sight line of a reclining guest. Align accent lights with the wall or artwork rather than the centre of the bed, and use wall washers to build ambient brightness instead of adding more ceiling points.

3. CRI, CCT and colour consistency across rooms

CRI Ra ≥ 90 is the baseline for hospitality. Skin tones, timber veneers, textiles and food all contain saturated reds that a low-CRI source flattens. Ask for the R9 value as well — a fixture can report Ra 90 while still rendering deep red poorly, which is exactly what guests notice in a restaurant or a bathroom mirror.

Colour temperature should be specified as a single project standard with a documented tolerance. Mixing 3000 K and 4000 K lamps across one corridor is visible even to untrained eyes. Specify one CCT across a zone, add a MacAdam step (3-step or better) to the schedule, and require samples from a single production batch for sign-off. Where tunable white is used, confirm the control protocol and the dim-to-warm behaviour with the driver supplier before the ceiling is closed.

4. Beam angle and spacing: the layout maths

Beam angle determines both the pool of light on the floor and how many fixtures the ceiling needs. As a starting point for a 2.7–3.0 m ceiling, a 36°–60° beam gives comfortable general illumination at roughly 1.2–1.5 m spacing; tighter 15°–24° beams are accent tools for artwork, tabletops and reception desks and need careful aiming.

Do not size the layout by wattage. Work from the required lux at the working plane, then verify with a DIALux calculation using the manufacturer’s IES or LDT file. A layout built on “one 15 W downlight per 4 m²” ignores ceiling reflectance, beam distribution and luminaire efficacy, and usually ends up either over-lit at the centre or dark at the perimeter.

5. IP rating for bathrooms, spas and covered exteriors

IP rating is an area-by-area decision, not a project-wide one. Guest room dry areas are adequately served by IP20 recessed fixtures. Bathroom zones above a basin or shower need IP44 or better on the visible face; spa, poolside and covered exterior soffits need IP65 with a sealed driver compartment and corrosion-resistant trim. Coastal and high-humidity projects should also ask about the finish and gasket material, since salt air attacks the trim long before it affects the LED.

Specifying one IP65 family across all wet areas keeps spares simple. Note that a higher IP rating often means a deeper housing and a different thermal path — confirm the ceiling void early rather than discovering it during installation.

6. Dimming and control: DALI, 0-10V or TRIAC

Choose the control layer at the same time as the fixture. DALI gives individual addressing, two-way status feedback and scene recall, which suits guest rooms, ballrooms and any space with a scene panel. 0-10V is simple, robust and inexpensive for corridors, back-of-house and large open zones where grouping is enough. TRIAC (phase-cut) remains common in refurbishments with existing mains dimmers, but driver compatibility and minimum load must be checked on a sample rig.

Whatever the protocol, require a dimming curve and a minimum dim level in the submittal. Flicker at low dim levels is one of the most common post-handover complaints in hotels, and it is a driver characteristic, not an LED one. For a fuller comparison of control protocols, see our guide to DALI vs 0-10V vs DMX512.

7. Five specification mistakes that cost hotel operators money

  • Issuing the fixture schedule before the ceiling void is confirmed — forces a late switch to surface-mounted units and breaks visual consistency.
  • Accepting “low glare” without a photometric file — UGR cannot be judged from a product photo.
  • Mixing CCTs or batches across one floor — visible colour banding that guests read as poor maintenance.
  • Specifying wattage instead of delivered lux — produces over-lit centres and dark perimeters.
  • Leaving the control protocol to the electrical contractor — driver and dimmer mismatches surface only at commissioning.

Quick spec checklist

ParameterTypical hotel targetWhat to request
Cutout / void depth75–200 mm, agreed with ceiling contractorDimensional drawing + installation clearance
GlareUGR < 19 guest rooms, < 22 circulationIES / LDT file and a room-level calculation
ColourCRI Ra ≥ 90, R9 stated, one CCT per zoneMacAdam step + same-batch samples
Beam36–60° general, 15–24° accentBeam data and DIALux layout
IngressIP20 dry / IP44 bathroom / IP65 wet & exteriorIP test report and finish specification
ControlDALI scenes or 0-10V zoningDimming curve, minimum level, compatibility list
DocumentationSubmittal pack before ceiling closureDatasheet, IES files, wiring diagram, warranty terms

Frequently Asked Questions

What cutout size should I allow for a hotel guest room downlight?

75–100 mm covers most general-illumination downlights in a standard guest room, with larger 150–200 mm units used in lobbies and high ceilings. Finalise the cutout against the actual ceiling void depth and the fire-rated assembly, not from a generic schedule.

Is CRI 90 really necessary, or is CRI 80 enough?

For hospitality, CRI Ra ≥ 90 is worth specifying. Wood, fabric, skin tones and plated food contain saturated reds that CRI 80 sources render flat. Ask for the R9 value too, since Ra alone does not describe red rendering.

Can one downlight family cover both dry rooms and bathrooms?

Often yes, if the range includes an IP65 version with the same trim and optics. That keeps the visual language consistent and simplifies spares. Confirm the deeper housing fits the ceiling void in wet areas before ordering.

Should a hotel project use DALI or 0-10V?

Use DALI where you need individually addressed fixtures, scenes and status feedback — guest rooms, ballrooms, restaurants. Use 0-10V for simple grouped zones such as corridors and back-of-house. Both are well established; the decision is about control granularity, not light quality.

What documentation should a supplier provide before the ceiling is closed?

At minimum: dimensional drawings, a full datasheet, IES or LDT photometric files, a DIALux layout at the target lux, wiring and control diagrams, IP and photometric test reports, and written warranty terms. If any of these are unavailable, the fixture is not ready to be specified.

Related reading and product ranges

More FEIDI buying guides

Planning a hotel or hospitality project? Browse the FEIDI commercial lighting range and the Xuanwu downlight series, or send us your ceiling plan — our engineers return a lighting layout with IES files and a DIALux simulation on request.

Leave a Comment

Your email address will not be published. Required fields are marked *